Wi-Fi weakens each time it passes through a wall, and the reinforced concrete walls of HDB flats and condos are especially hard on it, so rooms far from the router often get a poor signal. The fix is to place the router centrally and in the open, run network cables to key rooms during renovation, and add mesh Wi-Fi so every room has a strong signal.
Key takeaways
- Routers often sit near the main door, so the signal has to cross several concrete walls to reach the far bedroom.
- A central, open position for the router, away from walls and metal, is the first and cheapest fix.
- Renovation is the moment to run network cables to the rooms that matter, so each can have its own wired access point.
- Mesh Wi-Fi suits most flats better than a single range extender, especially where walls are thick.
- Smart switches and sensors often use their own low-power mesh networks, but the hub that links them to your home network still needs a good connection.
Why does Wi-Fi struggle in HDB flats and condos?
Concrete absorbs and reflects radio signals, and Singapore homes have a lot of it. The US National Institute of Standards and Technology (NIST) measured how radio signals weaken through common building materials, including brick, masonry block, several concrete mixes, reinforced concrete, glass, drywall and timber, at different thicknesses 1.
Layout makes it worse. StarHub notes that in most HDB flats and condos the router sits near the front door, so the signal has to pass through several concrete walls to reach the rest of the home 2. Singtel adds that older HDB flats with thick reinforced concrete walls can lose signal, especially in rooms farther from the router 3.
The household shelter, often called the bomb shelter, is the hardest room of all to reach, with its thick walls and steel door. Keep the router out of it.
Where should I put my router in an HDB flat?
As close to the middle of the home as you can, out in the open. Singtel's advice is to place the router centrally, because rooms farther away get weaker signals, and to keep it away from walls, metal and large objects 4.
In practice:
- Central: a living room console or a hallway shelf usually beats the corner by the main door.
- Open: not inside a closed cabinet, a metal box or the household shelter.
- Raised: at shelf height, not on the floor behind the TV.
- Connected by cable: if the fibre termination point is in a poor position, a network cable can carry the connection to a better spot.
For a new flat, decide this before your ID finalises the carpentry; see planning a smart home for a new BTO.
Should I run network cables during renovation?
Yes, if you can. A network cable to a room lets you put a Wi-Fi access point or mesh unit there with a fast, reliable link back to the router, which no amount of wireless tuning can match through concrete. It is much easier to run cables before plastering, false ceilings and carpentry than after.
| Room | Why it needs a network point | Typical use |
|---|---|---|
| Living room | Most devices, often the TV and console | TV, streaming box, mesh unit |
| Far bedroom | Usually the weakest signal in the flat | Mesh unit or access point |
| Study | Video calls need a stable link | Desk connection, mesh unit |
| Corridor or central ceiling | Best spot to cover several rooms | Ceiling access point |
| Smart home hub position | Links switches and sensors to the network | Hub or gateway |
Plan the network points at the same time as the electrical layout; see a typical renovation timeline.
Mesh Wi-Fi or a range extender: which is better for an HDB flat?
For most flats, mesh Wi-Fi. Mesh Wi-Fi is a system of several units placed around the home that work together as one network, with one name and password, passing your devices between units as you move.
A range extender simply repeats the router's signal. StarHub suggests an extender is best for a single dead spot in a small flat, while mesh suits flats such as 3-room units, and warns that adding a second extender tends to create more network names and more interference 2. Singtel recommends mesh as the better long-term solution for most homes, suggests starting with two Wi-Fi points where walls are thick, and advises checking the router's placement first 3.
Where you can, connect mesh units to each other with network cable, often called wired backhaul. The units then do not have to use their wireless capacity to talk to each other through the walls.
Which Wi-Fi band should my devices use?
Use the 2.4 GHz band for reach and the higher bands for speed. The 2.4 GHz band generally travels further through walls, while 5 GHz and 6 GHz carry more data over shorter distances.
Singapore's Infocomm Media Development Authority (IMDA) allowed the lower 6 GHz band, 5,925 to 6,425 MHz, for Wi-Fi use in 2023, opening it to Wi-Fi 6E devices 5. The extra band helps phones and laptops close to an access point, which is another reason to put access points in the rooms where you need speed.
How do smart switches and sensors stay connected?
Many smart home devices do not rely on Wi-Fi at all. Networks such as Zigbee and Thread are low-power mesh networks in which mains-powered devices, such as switches and lights, relay messages for each other 67. A home with smart switches in every room has relay points in every room.
The weak link is the hub or Thread border router that connects that mesh to your home network. Place it centrally, ideally on a wired network point, and it will serve the whole home. For a full explanation, see Matter, Thread, Zigbee and Wi-Fi.
How can I check my Wi-Fi coverage?
Walk the flat with your phone before renovation and again after. A simple check takes ten minutes:
- Stand in each room, including the far bedroom, the kitchen and the service yard.
- Run a speed test and note the result for each room.
- Repeat at night, when the household is online and the aircon is running.
- Mark weak rooms on your floor plan and give the list to your ID and electrician.
Our honest advice
Decide where the router, network points and any smart home hub go during the electrical stage, alongside the switches and lighting. A network planned with the rest of the home is invisible: you only notice it when it is missing. At Maxsen, our in-house electricians plan switch and network positions together across five visits from planning to handover, working with your interior designer and contractor. For condo owners, check your MCST's renovation rules before any cabling work; see smart home planning for condos.
Maxsen designs and installs smart homes in Singapore with its own team: planned with you, installed, and handed over working.
FAQ
Can Wi-Fi reach into the bomb shelter?
Often only weakly, because of the shelter's thick concrete walls and steel door. Avoid putting the router inside it, and expect devices inside to need a nearby access point.
Is a network cable worth it if I already have mesh Wi-Fi?
Yes. Mesh units connected by cable do not have to share their wireless capacity to talk to each other through concrete, so every room gets a stronger, steadier connection.
How many mesh units does a 4-room or 5-room HDB flat need?
It depends on the layout and wall thickness. Singtel suggests starting with two points where walls are thick 3; a longer flat or one with a far bedroom behind several walls may need more. Test each room after setting them up.
Why is my far bedroom always the weakest room?
The signal has crossed the most walls by the time it gets there, especially if the router sits near the main door 2. Moving the router to a central spot, or adding a wired access point in that room, is the usual fix.
Does my smart home need strong Wi-Fi in every room?
Not always. Switches and sensors on a low-power mesh relay messages between themselves 6, but cameras, speakers and the hub that links the mesh to your network do need a good connection.
Sources
- "Electromagnetic Signal Attenuation in Construction Materials." National Institute of Standards and Technology, 1997. nist.gov
- "Wi-Fi mesh setup guide." StarHub. starhub.com
- "Mesh Wi-Fi vs Wi-Fi extender for older HDB flats." Singtel. singtel.com
- "9 easy ways to improve weak WiFi at home." Singtel. singtel.com
- "IMDA allocates spectrum in 6GHz band for Wi-Fi." IB-Lenhardt, 2023. ib-lenhardt.com
- "Network Node Types." Silicon Labs Zigbee Fundamentals. docs.silabs.com
- "Thread." Matter Handbook, Connectivity Standards Alliance. handbook.buildwithmatter.com



